Corel Draw Knife Tool Tutorials

How to Use the Knife Puppet to Separate Objects

This teacher will attest a variety of ways to cut and cut objects using CorelDRAW's Knife tool. Please note that if you are using the Home and Student version of CorelDRAW Graphics Suite, the cut span and sketch options features are only available in the full interlingual rendition.

Click happening any of the images below to view full-size.

For our first example, this heart consists of cardinal curves: the red simple curve, and a pink curve for the highlight effect.

When you activate the Knife creature, by default it will exist lay to 2-Point Assembly line musical mode, which will slice the objective along a straight telephone line.

You john start the cut away on a point along the curve, or you can start in blank blank on the document. If you drag the slashed parentage and then that it only passes through the red fill, a faint cut line sack be seen and the Objects docker shows that the heart is at once split into two curves. Both curves are elite.

With the Pick tool, click on a blank area of the document to first deselect everything, then select just the lower portion and move it. To move the lead part, you need to select both the pink curve, which wasn't hand-hewn, and the red part of the tenderness.

In increase to piercing objects, the Knife tool can also slice through groups of objects. Start with the Saami heart example, this time make both objects into a group:

• Exercise the Pick tool to drag a selection just about the affectionateness to capture the ruddy and pink objects.
• Right-click on the selected objects and choose Group (or use keyboard shortcut Ctrl + G).

Activate the Knife tool again, and this meter choose Bézier mode for cutting.

Click points to name a jagged cut that goes through the garden pink spotlight and double-click when finished.

This results in a group of 4 objects, because the Knife tool sliced through some objects that earlier contain the group. At that place are now 2 red objects and 2 garden pink objects.

To create a broken heart, you'll need to select both objects within the group before moving the top and bottom portions apart.

How to Carve up Text

For the next example, here is some text surrounded by an outline.

Activate the Knife tool, choose the Freehanded reduce mode and set back the tier of freehand smoothing to about 80. Draw a wavy line across the text edition.

You butt select to turn Auto-close on Cut on operating theatre off. If you turn it on, it will close the outline along the cut edge of the text.

This military operation results in two separate groups. Each group has two objects: one is the text and the other is the synopsis.

With Auto-close-fitting on Cut turned off :

With Auto-close on Cut turned on :

Outline Options of the Tongue Tool

The Outline options let you to take whether to change outlines to curves or keep them as outlines when ripping objects. By default, the Outline options are set to Automatic, which means that CorelDRAW will choose the selection that best preserves the abstract appearance.

To demonstrate the difference of opinion in Outline options, a rippled slew has been created with the Playpen tool, with a start and end arrowhead.

After splitting this curve with the Automatic schema option, both ensuant objects remain curves.

The Win over to Objects outline option would produce the same results. But using the Keep Outlines option, all part of this split aim retains the same arrow properties.

Adding Gaps with the Stab Tool

The Knife tool can also add gaps. In this example we have a graphic for a window banner, and gaps are needed where the window frames testament represent. Guidelines have been added to mark where the gaps should exist.

Activate the Knife tool and choose 2-Point Melodic phras modality, take Gap from the Hack Span dropdown list, and set a breadth. Pose the Outline Option back up to Automatic.

Drag the cut lines along the guide lines, holding descending the Shift operative to keep the lines erect.

The resultant gaps are centered on the cut lines.

Adding Overlaps with the Stab Tool

For the cobbler's last example, here is a graphic that is to Be written as a split battlefront on a sports jersey. Printing this graphic will require an overlap on the center, where the two sides of the jersey will button together.

Aerate the Knife tool and choose 2-Point Line mode, choose Lap from the Cut Span dropdown tilt, and set a width. Lay the Limn Option back to Semiautomatic.

Keeping down the Shift samara, hang back the cut line weak along the center.

Today, if you apply the Pick tool to select everything on extraordinary side of the graphic and move the selection belt down, the lap can be clearly seen.

Corel Draw Knife Tool Tutorials

Source: https://learn.corel.com/tutorials/split-objects-with-the-knife-tool/

Share this post